1. Why a warehouse Wi-Fi is not an office Wi-Fi
In a warehouse, the wireless signal meets obstacles that do not exist in an office. Metal racking reflects and absorbs radio waves, creating shadow zones between one aisle and the next. Doors, trolleys, goods containing a lot of metal or water, and machinery change how the signal propagates, in ways that shift from day to day. A test run in an empty warehouse says little about how the network will behave with real goods and loads.
The problem becomes serious when handheld terminals are used to pick, confirm and move goods. If an operator loses the connection halfway through a pick, the operation stops or is recorded incorrectly, and the manager discovers the error only at the end of the shift. For this reason the network must be designed around the real paths of people and vehicles, not just the floor plan of the covered area, and tested during the busiest working hours.
2. What to prepare before the site survey
Before calling an installer, gather some information. The more precise it is, the less time the survey takes and the less risk there is of paying twice for the same work. You do not need a perfect project: you need a clear picture of how the warehouse works every day, including the moments when things go wrong, because the network must be designed for those moments.
Bring with you, or have your manager prepare, at least the items on the list. The provider will then confirm or correct them on site, and every missing item lengthens the survey and makes the estimate less reliable. If a piece of data is not available, still write it down as a doubt: even an admission of uncertainty helps direct the measurements. It is also worth asking for an estimate of the working time.
- Up-to-date floor plan, showing racking, doors, loading bays and storage areas.
- List of the handheld terminals and vehicles that stay connected, with model and use.
- Typical paths of operators and trolleys, with the points where they stop.
- Peak shifts and periods when the volume of movements increases.
- Continuity requirements: what must remain operational if the network goes down.
3. Steps to design the coverage
The design is built from the work points and paths, not from the floor area. Follow this sequence with the provider, so that every decision has a verifiable reason and does not rest only on the installer's impression. Note the decisions as you make them. Each step produces a result that feeds the next: if one is unclear, stop and ask for an explanation before moving on.
The final output is a document with positions, measured paths and reasoned choices, which the provider should hand over before installation. You need it to compare different offers on the same basis and to check, after the work, that what was installed matches what was agreed. Ask that it also include the list of installed devices and the acceptance test date. Keep it together with the updated floor plan.
- Map the work areas: where goods are picked, confirmed and loaded.
- Record the real paths of operators and trolleys, with the stopping points.
- Carry out a survey with signal measurement tools, walking the actual paths.
- Choose access point positions, preferably high up and with a clear line of sight where possible.
- Plan a controlled overlap between access points along the paths, so that handover between them is uninterrupted.
- Separate the networks: terminals, administration, guests and industrial devices on distinct segments.
- Define how each terminal authenticates and how it is blocked if lost.
4. Common mistakes to avoid
The first mistake is installing access points where cabling is convenient, not where the signal is needed. An access point placed near an office but far from the racking leaves exactly the busiest aisles uncovered. The second mistake is using a single network for everything: terminals, administrative computers, guests and industrial devices share the same space, and one compromised device becomes a way in.
A third mistake is relying on a single check made at installation. The network changes with the goods, with peak seasons and with the addition of new vehicles. Excess power is not always a solution either: it can create interference between nearby points and worsen link quality. A fourth, less visible mistake is forgetting printers and readers, which change the network traffic.
5. Checking that the network works
The check must be done under real working conditions. Walk the paths with a terminal in hand, carrying out typical operations: picking, confirming, moving. Make sure the connection never drops during the handover between one access point and the next. Repeat the test at a time of heavy traffic, because a network that copes with a few people may not cope with everyone.
Record the results in a simple document: path, critical point, outcome, time and conditions at the moment, such as the number of people on the floor and vehicles in motion. A result without context is no use for repeating the test in a comparable way. This document is the proof that the network was commissioned, and it becomes the reference for later checks and for any interventions by the provider.
6. What to do after coverage is in place
A working network must be managed. Keep an up-to-date inventory of access points and terminals, with the owner of each and the status of updates. A terminal that is not updated, or no longer in use but still has active access, is a risk that builds up silently. Every decommissioning should close its access the same day. Also keep the configuration records, so that a replacement can intervene without starting from scratch.
Plan a periodic coverage check, especially after layout changes, new racking or the arrival of new equipment. Ask the provider whether terminal management can be centralised, so that a device can be blocked remotely if lost. A check after every change costs little compared with a sudden shutdown of the department, and it makes it easier to tell whether a problem comes from the network or from a device.
7. How to start
The first step this week is to gather the floor plan and the list of terminals. With these two documents you can ask any provider for a proper site survey, instead of an estimate based on a few photographs. Also note two or three points where the signal drops today and where work stops most often. Ask shift managers which are the worst moments of the week, as these are the ones to test first.
Then ask the provider to explain how they intend to verify coverage on the real paths and how they will separate the networks. If the answer remains generic, treat that as a signal to dig deeper before deciding. The decision must rest on measurements taken in your warehouse, not on promises. Also ask for a concrete reference to a similar installation already completed, to be checked directly with the client who received it.
Frequently Asked Questions
Why does the signal drop precisely between the racking?
Metal structures reflect and absorb radio waves, creating shadow zones behind and between the shelves. The signal can bounce and weaken differently depending on the position of the operator and the load. That is why a site survey with on-site measurements is needed, rather than a generic rule. The provider can choose access point positions and orientations based on what is measured.
Do handheld terminals need a separate network?
In most cases it is better to separate terminals from administrative and guest networks. A compromised or lost terminal must not be able to reach office computers or management systems. Separation is achieved with dedicated segments and rules that allow only the necessary traffic. Check with the provider how these rules are configured.
Does increasing access point power solve the problem?
Not always. Excess power can create interference between nearby points and worsen link quality. It is often more effective to position the devices better and plan a controlled overlap along the paths. The solution depends on the layout and must be verified with measurements, not just by adjusting settings.
Who manages lost or decommissioned terminals?
There must be a clearly named owner for each terminal. When a device is lost, replaced or decommissioned, its access to the network and to the management system must be revoked immediately. If management is centralised, blocking can be done remotely. Keep an up-to-date register of devices and their users, and review it at regular intervals.
Is Wi-Fi enough for the whole warehouse, or are other technologies needed?
For many warehouses Wi-Fi is sufficient if designed around the real paths. In very large areas, outdoors or with many moving devices, alternatives such as private 5G or a dedicated radio may be worth evaluating. The choice depends on the extent, the mobility and the services that must remain active. Compare the options with the provider before deciding.