GUIDE · BUSINESS NETWORK

Wi-Fi site survey: how to plan coverage before installing access points

After this guide you will know what a radio survey is, how to prepare for one, what to measure on site and how to use the result to decide where to place access points. The survey prevents you from discovering inadequate coverage once the installation is finished, when correcting it costs more.

Updated october 2026
7 min read
Altovar Technical Editorial Team

1. What a site survey is and why it pays off

A site survey, or radio survey, is a direct measurement of how the Wi-Fi signal propagates through a building. It does not install the network; it decides where the network should be installed. Walls, floors with metal structures, furniture, people and even kitchens change how signals travel in ways that are hard to predict from a floor plan. This is why an access point placed “by eye” may cover the office at the front well and the meeting room at the end of the corridor poorly.

A survey is especially worthwhile when the building is large, when there are thick walls or glazing with coatings, when rooms have different uses, or when the network must support telephony, video or delay-sensitive applications. It also helps avoid interference from neighbouring networks, which in a shared building are more common than many people think. If Wi-Fi also serves sensors or industrial devices, the survey should be repeated taking those devices and their antennas into account.

2. Before the site visit: what to prepare

The survey starts with documents. Obtain the updated floor plan of each level, showing load-bearing walls, suspended ceilings, technical cupboards and the position of existing network sockets. If no floor plan exists, a hand-drawn sketch with approximate measurements is still better than nothing, provided it is declared as such. Also ask whether other access points or wireless networks are active nearby, because they are a source of interference that must be known in advance.

Define the usage goals for each area: workstations, meeting rooms, warehouse, guest areas. A warehouse with metal shelving has different needs from an open-plan office. Also write down which devices will use the network and which applications require continuity, such as Wi-Fi calls or video conferences. These requirements determine the level of coverage to verify in each zone.

3. How the survey is carried out on site

The survey measures the signal at several points in the building, following a grid or a walking route. The engineer uses an instrument that records signal strength, the ratio of signal to noise and the channels occupied by other networks. Measurements must be taken with the rooms in their real condition of use, not empty, because people and furniture absorb part of the signal and change the result.

In a later phase the engineer may run a trial with a temporary access point, moving it between candidate positions. This trial shows how coverage changes with position and helps choose the best compromise between coverage, interference and the number of devices. The result is a map for each floor, showing which areas meet the requirements and which do not.

4. Reading the map: what to look for

The map should be read by area, not by colour. An area with strong signal but a lot of noise can be worse than an area with medium signal and little noise. Look for dead zones, meaning points where the signal falls below the required threshold, and areas where too many access points are visible at once, which cause interference on the same channel. An area with a medium but stable signal is often more useful than one with a high signal that fluctuates.

Check also the overlap between cells: two nearby access points should cover areas that overlap somewhat, to allow moving devices to roam, but not too much, to avoid interfering with each other. If the map shows this balance, the design is coherent. If it shows coverage only, ask what was measured for noise and interference. Note any areas where handover between access points is interrupted, because it is the clearest sign of badly calibrated overlap.

ObservationWhat it meansTypical action
No usable signal in an areaInsufficient coverage at that pointMove or add an access point
Good signal but a lot of noiseInterference from other networks or appliancesChange channel or power, review position
Too many access points visible in one areaCells overlapping on the same channelReduce power or replan channels
Strong signal outside the premisesCoverage spilling out of the buildingReduce power at the edges

5. Common survey mistakes

A survey fails more often because of methodological errors than instrument errors. The problem is almost always a measurement taken under conditions different from real use, or a conclusion drawn from too few tests. Ask the provider how it conducted the survey and which conditions it verified. A measurement without a description of the environment is hard to compare with a future one.

  • Measuring in empty rooms and then discovering that coverage drops when people are present.
  • Using a single test access point and generalising the result to the whole floor.
  • Ignoring sources of interference outside the company, such as neighbouring networks.
  • Overlooking floors above and below, where the signal passes through the floor slabs.
  • Planning coverage alone without planning capacity, meaning how many devices each access point can support together.

6. From survey to design: positions and equipment

The provider should deliver the map, the chosen positions, the channels assigned and the results of the measurements taken after installation. If any of these parts is missing, you cannot verify that the network does what was promised. The cabling connected to each access point must be tested, because a faulty cable produces irregular coverage that looks like a radio problem. Without these final measurements, a coverage guarantee remains a statement without proof.

  1. Mark the candidate positions and the expected coverage area of each access point on the floor plan.
  2. Verify that each position has a network socket and a reachable cabled route.
  3. Check the power required by each access point and the capacity of the switch that serves it.
  4. Compare the coverage obtained with the written requirements for each area.
  5. Repeat the measurement at critical points after installation and keep the result.

7. How to start

This week, take the floor plan of one level and mark the areas where Wi-Fi causes problems for users. Ask colleagues to note where they lose connection or where speed drops, with the time of day. This list is your first survey, even before you call an engineer, and it makes the site visit far more effective. Use the same floor plan with the provider, so that reports share a common reference.

Then ask the provider for a survey that declares its conditions, instruments and method, and that delivers a map per floor showing covered and uncovered areas. If the provider proposes installing access points without this step, ask why: the answer says a great deal about the method it will use for the rest of the project. Also ask for the map to be delivered in an editable format, not only as a static image.

Frequently Asked Questions

How much does a site survey cost?

The cost depends on the size of the building, the number of floors, the complexity of the premises and the level of detail required. The survey of a single room is very different from that of a multi-floor building with mixed areas. Ask for a quote that describes the scope, the method and the form of the deliverable, so that you can compare proposals on a like-for-like basis.

Can I do a site survey with a phone app?

Measurement apps help you understand the signal roughly, but they do not replace professional equipment or a repeatable survey. They can be useful for a first map of problem areas to bring to the engineer. To decide where to install equipment you need a survey that also records interference and channels.

Does a site survey need to be repeated after every change?

It should be repeated when the use of the rooms, the structure of the building or the number of devices changes significantly. Moving a desk usually does not require a new survey, whereas adding a meeting room or changing the walls does. Keep the initial survey together with the conditions under which it was carried out, so that results can be compared.

Is one measurement enough for the whole building?

No. Each floor, and often each area with different materials, has its own radio behaviour. A survey carried out on one floor does not describe what happens above and below, where the signal passes through the slabs. Ask for a map for each floor and for critical areas to be measured separately.

Can the provider guarantee a specific speed?

A serious provider should not promise a fixed speed per device without knowing the load, number of users and internet connection. Wi-Fi shares the channel among all devices, so the perceived speed depends on total traffic. Ask which parameters will be verified and how, and have the stated limits explained in writing.

About this content

General informational guide. Regulations and technical requirements change over time: always check the official sources and assess your specific case with a qualified technical or legal advisor.

GET IN TOUCH

Talk to our team.

We'll show how Altovar integrates into your infrastructure. No commitment, no sales pitch. Just a technical conversation.

BOOK A DEMO →